Mordant Solution - T Wash - galvanised steel pre etch primer 500 ml
Mordant Solution - T Wash - galvanised steel pre etch primer 500 ml
Code: 0
£ 24.99
Mordant Solution.
 
Mordant solution for Galvanised Steel 500 ml 
Apply to new galvanising within 7 days. Zinc surfaces which are contaminated should be cleaned down using an abrasive pad, water and cleaning agent followed by rinsing and allowing to dry. If contaminated with oil or grease surfaces should be wiped over with Universal Degreaser before carrying out the cleaning down procedure. Can be applied to weathered galvanised surfaces although reactivity of the treatment will diminish as the age of the galvanising increases and can result in an uneven colouration from light grey to dark grey. If no colour change take place, these areas should be considered as contaminated. 
HOW TO USE MORDANT SOLUTION (T-WASH)
 
  PRODUCT INFORMATION CARBUSONIC MORDANT SOLUTION
 Prepares New Galvanised Metal 
Chemically Etches Galvanised Surfaces 
Water-Based Product 
Typical Use; 
Suitable for use on new galvanised metal. 
Colour Range ; 
Blue Colour in container. 
SURFACE PREPARATION 
  To get the best results, ensure surfaces to be 
painted are sound, clean and dry (new surfaces 
particularly must be fully dry) and free from all 
defective or poorly adhering material such as dirt, 
grease and wax. 
Degrease where necessary with a suitable oil and 
grease remover. Rinse with clean water to remove 
residues. 
  APPLICATION INFORMATION 
Apply a liberal coat of  Mordant 
Solution by brush and allow to dry. If the surface 
fails to turn black overall, the most likely cause is 
contamination of the surface or the presence of a 
factory applied pre-treatment. Rinse the surface 
thoroughly and abrade, using a suitable abrasive 
paper. Remove all residues and re-apply, Avoid over-application 
as pooling of the wash will result in the formation 
of a fine brown deposit of copper. 
After treatment the surface must be rinsed with 
clean water to remove all residues and then 
allowed to dry before priming. 
The pre-treated surface should be over coated 
with an appropriate  metal primer 
within 48 hours or before contamination can 
repeat.
   
APPLICATION METHOD 
Brush only. Do not spray. 
Practical Coverage 
10 meters squared per litre
 
 
Carbusonic LTD are recognised suppliers to The Royal Navy anti corrosion Aircraft husbandry Team.
 
Mordant solution for Galvanised Steel 500 ml 
Apply to new galvanising within 7 days. Zinc surfaces which are contaminated should be cleaned down using an abrasive pad, water and cleaning agent followed by rinsing and allowing to dry. If contaminated with oil or grease surfaces should be wiped over with Universal Degreaser before carrying out the cleaning down procedure. Can be applied to weathered galvanised surfaces although reactivity of the treatment will diminish as the age of the galvanising increases and can result in an uneven colouration from light grey to dark grey. If no colour change take place, these areas should be considered as contaminated. 
HOW TO USE MORDANT SOLUTION (T-WASH)
 
  PRODUCT INFORMATION CARBUSONIC MORDANT SOLUTION
 Prepares New Galvanised Metal 
Chemically Etches Galvanised Surfaces 
Water-Based Product 
Typical Use; 
Suitable for use on new galvanised metal. 
Colour Range ; 
Blue Colour in container. 
SURFACE PREPARATION 
  To get the best results, ensure surfaces to be 
painted are sound, clean and dry (new surfaces 
particularly must be fully dry) and free from all 
defective or poorly adhering material such as dirt, 
grease and wax. 
Degrease where necessary with a suitable oil and 
grease remover. Rinse with clean water to remove 
residues. 
  APPLICATION INFORMATION 
Apply a liberal coat of  Mordant 
Solution by brush and allow to dry. If the surface 
fails to turn black overall, the most likely cause is 
contamination of the surface or the presence of a 
factory applied pre-treatment. Rinse the surface 
thoroughly and abrade, using a suitable abrasive 
paper. Remove all residues and re-apply, Avoid over-application 
as pooling of the wash will result in the formation 
of a fine brown deposit of copper. 
After treatment the surface must be rinsed with 
clean water to remove all residues and then 
allowed to dry before priming. 
The pre-treated surface should be over coated 
with an appropriate  metal primer 
within 48 hours or before contamination can 
repeat.
   
APPLICATION METHOD 
Brush only. Do not spray. 
Practical Coverage 
10 meters squared per litre
 
 
Carbusonic LTD are recognised suppliers to The Royal Navy anti corrosion Aircraft husbandry Team.
Customer Reviews (0)